February 19, 2024
We all know that the kitchen is the most smouldering place, so now almost every family will install a Range Hood, which can help us to remove excess fumes, so that there will be no pungent smell of soot in our kitchen. So what are the installation requirements for the range hood pipe ? What steps do you need to know about the installation of the range hood pipe? Let's introduce you to the small series of the decoration home network below.
First, the range hood installation requirements
1. Mandatory regulations for installation of natural gas installation: When installing gas pipelines indoors, it is strictly forbidden to install gas pipelines and facilities in bathrooms, study rooms, bedrooms, etc. where air circulation is not good enough or temporary rest. In addition, it is strictly forbidden to use the in-line gas water heaters that have been eliminated by the state, because the household appliances in the direct-discharge gas water heaters will directly discharge the exhaust gases in the room, which will also cause indoor people to carbon monoxide poisoning.gas cooktops,cooktop gas,glass gas cooktop,table gas cooker cooktop,hob gas cooktop
2. Relevant regulations on kitchen renovation. Because there is a gas inlet for the pipeline in the kitchen, the kitchen location cannot be changed at will. If you must change, you must also consult the housing design unit, and the design change order will be issued by the housing design unit. The kitchen must have an explosion-proof system and ventilation system after renovation, to prevent gas explosion or personnel carbon monoxide poisoning. In addition, if you just want to change the gas pipeline in the kitchen, you must ask a professional to operate. Failure to follow the specifications or arbitrarily dismantle the gas pipeline or replace the joints is very easy to cause safety hazards, which may cause serious danger to life.
3. General provisions for the installation of natural gas pipelines. During the laying of gas pipelines, there may be situations where other pipelines meet, and the net distance between the pipelines and the pipelines is strictly required. Only in this way can the safety gas pipeline installation be standardized. For horizontal parallel laying, the clearance should not be less than 150mm; when laying vertically parallel, the clearance should not be less than 100mm, and should be located outside the other pipelines; when crossing, the clearance should not be More than 50mm. When using gas every day, it is mainly necessary to prevent gas leakage from gas pipelines.
Second, the range hood pipe installation steps
1. The installation position of the range hood is on the same axis line above the cooker and the cooker on the same axis line. The height of the bottom end of the top suction hood is 65-75cm, and the bottom end of the side suction hood is 35-. 45cm. According to the size of the specific hood product, find the position where the gusset is installed on the back and draw the line with a pencil.
2. Be sure to pass the property's consent before opening the window or wall; secondly, pay attention to the safety problem. Generally, the end of the exhaust pipe is made of metal. If the hole is too small, the heat transfer of the metal may cause the glass to burst and hurt. Pedestrians, and the pipe leads to the window, the strong north wind blowing will cause the fumes to infuse. It is best to extend the pipe to the lower nest after it has been extended, so as to prevent rain from flowing into the pipe when it rains and to block the wind.
3. If the secondary flue has been removed, or if it is necessary to prevent the smoke from being better, use a flue check valve. Under normal circumstances, the effect of the check valve of the range hood is not very obvious, and the installation of the check valve in the flue can protect the range hood so that the smoke in the flue will not be poured into the pipeline and the range hood. However, after installing the check valve, it should be cleaned regularly. Otherwise, the check valve will be opened and lose its effect, and the flue check valve should be replaced once every two years or so.
There is definitely a range hood in our kitchen. It has a lot of help for us. So what are the steps and procedures for the installation of the range hood? I think you can understand it through the introduction of Xiaobian, then if everyone Also want to know more about decoration information, please continue to pay attention to the decoration home Internet cafe.
More related wonderful reading:
How to reform the gas pipeline? How much is the gas pipeline renovation?
Pipeline valve classification pipe valve installation
How to transform the gas pipeline? Gas pipeline renovation strategy
The above is the Range hood pipe installation requires range hood pipe installation steps we have listed for you. You can submit the following form to obtain more industry information we provide for you.
You can visit our website or contact us, and we will provide the latest consultation and solutions
Send Inquiry
Most Popular
lastest New
Send Inquiry
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
